Cooper Security 9853 Guida di Installazione Pagina 81
- Pagina / 102
- Indice
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
4. Programming
496791 75
Third Downloader Telephone Number (Commands 120)
Use this option to enable Downloader to use a third callback number (inde-
pendent of Commands 118 and 119). Before the Downloader has made a
connection, the remote PC operator keys in the third callback number and
<Downloader> transmits it to the control unit. The control unit then uses that
number to call back to the remote PC.
Key in Option 0 to disable the third callback number, or option 1 to enable it.
Fast Format Channels (Command 121)
If you selected Fast Format reporting type in Command 103 then you can
use Command 121 to allocate one of the following events to each of the 8
channels:
00 Not used 11 AC Fail
01 Fire 12 Tamper Alarm (Day tamper)
02 PA 13 Open (see note 1)
03 Burglar 14 Close (see note 1)
04 Open/Close 15 Zone Omitted (see note 2)
05 Alarm Abort 16 Medical Assistance
06 Technical Alarm 17 Key Box
07 Alarm Confirmation 18 Anti Mask
08 RF Low Battery 19 Smoke Detector
09 Supervision Loss 20 Comms Acknowledge
10 RF Jamming
Notes:1. 13 Open and 14 Close provide the same functions as 4 Open/Close, but on
two separate channels.
2. 15 Zone omitted - the control unit sends this signal for five seconds when a
user omits a zone.
3. The control unit sends 08 RF Low Battery when the radio detector with a low
battery causes an alarm or sends a supervision signal. To enable this facility in
day mode set Menu 37 to option 1.
4. The control unit delays reporting/loging either mains loss, or exiting engi-
neering with mains loss, by 15-18 min (chosen randomly). If you chose a
Scandinavian default in Command 0 then the control unit waits at least 60
minutes before reporting.
Communication Acknowledge (Command 122)
Option 1 of this Command will be available if you select option 1 (Ireland) in
Command 0. In addition, the option is only effective if you have selected Scan-
com Fast format in Command 103.
Once the communicator has made a call and the ARC returned an acknowl-
edgement then with this Command enabled the keypad will display the
message “Call your CS” and beep for 10 seconds when the system is unset
or disarmed. To clear the display the user must enter a valid access code.
- INSTALLATION AND 1
- PROGRAMMING GUIDE 1
- Contents 3
- 496791 iii 5
- 1. INTRODUCTION 7
- 2 496791 8
- 496791 3 9
- System Features 10
- Detectors 10
- 9955 Radio Expander 10
- Partioned or Single System 11
- User Control 11
- Configurations 11
- 6 496791 12
- 2. Technical Description 13
- Compatible Equipment 14
- Control Unit PCB 15
- 9954 Expander 16
- 3. INSTALLATION 17
- Cabling Keypads and Expanders 18
- Fitting the System 19
- Fitting the Control unit Case 19
- Fitting a 9930 Keypad 19
- Wiring the Control Unit 20
- Cable Entries 20
- Mains Connection 20
- Remote Keypads 21
- 16 496791 22
- Detector Circuit Connections 23
- 18 496791 24
- Connecting Expanders 25
- Expander Addressing 26
- Using Programmable Outputs 26
- Wiring Keyswitches 27
- Using a Communicator 28
- Statutory Information 29
- Application 29
- Compatible PABXs 29
- Approval 29
- Safety Notice 30
- Connecting the Telephone Line 31
- 26 496791 32
- 496791 27 33
- Fitting a Battery 34
- Initial Start Up 35
- 30 496791 36
- 4. Programming 37
- 32 496791 38
- 496791 33 39
- 34 496791 40
- 496791 35 41
- 36 496791 42
- 496791 37 43
- 38 496791 44
- Communications Programming 45
- 40 496791 46
- 496791 41 47
- 42 496791 48
- Leaving Programming Mode 49
- Engineer Reset 49
- Re-entering Programming Mode 49
- Programming Reference 50
- Country Defaults (Command 0) 50
- 496791 45 51
- 46 496791 52
- 496791 47 53
- 48 496791 54
- 496791 49 55
- RedCare Reset (Command 23) 56
- Status Display (Command 28) 57
- 52 496791 58
- System Reset (Command 33) 59
- PA Reset (Command 34) 59
- Alarm Abort (Command 36) 59
- 54 496791 60
- Bell Delay (Command 41) 61
- 56 496791 62
- CSID Code (Command 50) 63
- Abort Reset (Command 53) 64
- BVVO Supervision (Command 54) 64
- Sounder Tamper (Command 59) 65
- 60 496791 66
- 496791 61 67
- 62 496791 68
- 496791 63 69
- 64 496791 70
- 496791 65 71
- 66 496791 72
- 496791 67 73
- Call Mode (Command 101) 74
- Reporting Type (Command 103) 75
- 70 496791 76
- Dynamic Test (Command 108) 77
- Rings to Answer (Command 112) 78
- Access Mode (Command 114) 78
- Account Number (Command 117) 79
- 74 496791 80
- 496791 75 81
- 76 496791 82
- Report Mode (Command 131) 83
- 78 496791 84
- 496791 79 85
- 80 496791 86
- 496791 81 87
- Partition Programming 88
- Introduction 88
- Command Changes 89
- 84 496791 90
- ACPO DD243: 2002 Compliance 91
- Alarm Filtering 92
- 5. Testing 93
- Keypad and Event Log Displays 94
- 496791 89 95
- Printing the Log 96
- 496791 91 97
- 92 496791 98
- 496791 93 99
- 94 496791 100
- 496791 95 101
- DECLARATION OF CONFORMA NCE 102
Prodotti e manuali riguardandi Sistemi di controllo di accesso Cooper Security 9853
(44 pagine)© 2020, manymanuals.it. Tutti i diritti riservati | 0.024 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commenti su questo manuale