Cooper Security 9853 Guida di Installazione Pagina 7
- Pagina / 102
- Indice
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
496791 1
1. Introduction
1. INTRODUCTION
The 9851 is designed to be fully programmable to suit individual site require-
ments and user needs.
The system comprises a control unit in a shielded case, up to four separate
keypads and one keyswitch interface (see Figure 1 on the next page). You
should always fit at least one keypad.
The control unit provides:
° A four-wire bus connection for keypads, keyswitches and hard-wired or
wireless zone expanders.
° Connections for either Closed Circuit, Fully Supervised Loops, or End
of Line resistor zones.
° Connections for four fully programmable outputs.
° Internal sounder loudspeaker output with electronically generated
Chime, Alarm, Fire and Entry/Exit tones. (The volume of the Entry/Exit
and Chime tones can be adjusted).
° Built in communicator for reporting to an Alarm Receiving Centre
(ARC).
° Pins for fitting any plug-on communication device that complies with
the Scantronic plug-on footprint.
° Pins for fitting a plug-by communication device.
° Local or remote downloading.
The control unit provides connectors for eight Closed Circuit (CC) zones or
16 Fully Supervised Loop (FSL) zones on its own printed circuit board.
Separate expander units allow connection of further zones up to a total of 40.
The 9954 expander provides eight wired zones. Alternatively, a 9955 ex-
pander allows connection of eight wire-free zones.
The control unit supports the 9930 sixteen character Liquid Crystal Display
(LCD) keypad. In addition the control unit also supports the 9928 keyswitch
interface.
As an Installer you can program the system either from the keypads, or using
PC based Windows <Downloader>. When programming from the keypads
the programming interface is arranged as a set of three-digit numbered
commands similar to those used by the 9800 family of products.
The system can provide for up to 16 separate users. User facilities include:
° Four different security levels which can be programmed by the Installer
as either full set and three part sets, or four independant partitions.
° User programmable Duress code.
- INSTALLATION AND 1
- PROGRAMMING GUIDE 1
- Contents 3
- 496791 iii 5
- 1. INTRODUCTION 7
- 2 496791 8
- 496791 3 9
- System Features 10
- Detectors 10
- 9955 Radio Expander 10
- Partioned or Single System 11
- User Control 11
- Configurations 11
- 6 496791 12
- 2. Technical Description 13
- Compatible Equipment 14
- Control Unit PCB 15
- 9954 Expander 16
- 3. INSTALLATION 17
- Cabling Keypads and Expanders 18
- Fitting the System 19
- Fitting the Control unit Case 19
- Fitting a 9930 Keypad 19
- Wiring the Control Unit 20
- Cable Entries 20
- Mains Connection 20
- Remote Keypads 21
- 16 496791 22
- Detector Circuit Connections 23
- 18 496791 24
- Connecting Expanders 25
- Expander Addressing 26
- Using Programmable Outputs 26
- Wiring Keyswitches 27
- Using a Communicator 28
- Statutory Information 29
- Application 29
- Compatible PABXs 29
- Approval 29
- Safety Notice 30
- Connecting the Telephone Line 31
- 26 496791 32
- 496791 27 33
- Fitting a Battery 34
- Initial Start Up 35
- 30 496791 36
- 4. Programming 37
- 32 496791 38
- 496791 33 39
- 34 496791 40
- 496791 35 41
- 36 496791 42
- 496791 37 43
- 38 496791 44
- Communications Programming 45
- 40 496791 46
- 496791 41 47
- 42 496791 48
- Leaving Programming Mode 49
- Engineer Reset 49
- Re-entering Programming Mode 49
- Programming Reference 50
- Country Defaults (Command 0) 50
- 496791 45 51
- 46 496791 52
- 496791 47 53
- 48 496791 54
- 496791 49 55
- RedCare Reset (Command 23) 56
- Status Display (Command 28) 57
- 52 496791 58
- System Reset (Command 33) 59
- PA Reset (Command 34) 59
- Alarm Abort (Command 36) 59
- 54 496791 60
- Bell Delay (Command 41) 61
- 56 496791 62
- CSID Code (Command 50) 63
- Abort Reset (Command 53) 64
- BVVO Supervision (Command 54) 64
- Sounder Tamper (Command 59) 65
- 60 496791 66
- 496791 61 67
- 62 496791 68
- 496791 63 69
- 64 496791 70
- 496791 65 71
- 66 496791 72
- 496791 67 73
- Call Mode (Command 101) 74
- Reporting Type (Command 103) 75
- 70 496791 76
- Dynamic Test (Command 108) 77
- Rings to Answer (Command 112) 78
- Access Mode (Command 114) 78
- Account Number (Command 117) 79
- 74 496791 80
- 496791 75 81
- 76 496791 82
- Report Mode (Command 131) 83
- 78 496791 84
- 496791 79 85
- 80 496791 86
- 496791 81 87
- Partition Programming 88
- Introduction 88
- Command Changes 89
- 84 496791 90
- ACPO DD243: 2002 Compliance 91
- Alarm Filtering 92
- 5. Testing 93
- Keypad and Event Log Displays 94
- 496791 89 95
- Printing the Log 96
- 496791 91 97
- 92 496791 98
- 496791 93 99
- 94 496791 100
- 496791 95 101
- DECLARATION OF CONFORMA NCE 102
Prodotti e manuali riguardandi Sistemi di controllo di accesso Cooper Security 9853
(44 pagine)© 2020, manymanuals.it. Tutti i diritti riservati | 0.047 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commenti su questo manuale