Cooper Security 9853 Guida di Installazione Pagina 77
- Pagina / 102
- Indice
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
4. Programming
496791 71
Dynamic Test (Command 108)
In dynamic testing the system makes a test call 24 hours after the last
communication. Select option 0 to disable dynamic test calls. Select option 1
to enable dynamic test calls.
Note: Cooper Security Ltd recommend that you chose either Static Test Call (105) or
Dynamic Test Call, but not both at the same time.
Three Way Call - UK only (Command 109)
To use Three Way Call you must make sure that the BT Network Services
Option of ‘Three Way Calling’ is available on the telephone line to which the
communicator is connected.
Three way off (0) Disabled
Three way on (1) Three Way Call.
Operation: If the control unit triggers the communicator
and the communicator detects Off Hook or Incoming
Ringing, the communicator then sends a 80 ms trigger
(which represents the “R” or Recall button on a tel-
ephone) which is detected by the exchange as a request
for a new clean line. With the new line available, the
communicator then attempts to connect to the pre pro-
grammed receiver number.
Engineer Download (Command 110)
The control unit can be programmed from a PC using <Downloader> soft-
ware. You can connect the PC to the control unit either over the telephone
network, or locally using a cable.
Use Command 110 to manually connect the control unit to the PC.
Local (0) To connect the control unit to a PC (for example a laptop)
using a local cable key in 110 0 .
Remote (1) To automatically answer calls coming from a remote PC
over the telephone network key in 110 1 . You will
also need to use Commands 112, 113. (Note that Secure
callback does not work with this option.)
Note: The control unit will leave Command 110 if <Downloader> does not make a
call within 30 minutes.
While the control unit is connected to the PC you can upload its programming
configuration into <Downloader> in order to inspect it. Using <Downloader>
you can change the configuration and then transmit the new configuration
back to the control unit. If you do not wish to change the configuration you
can simply monitor the state of the control unit and zones from the PC.
- INSTALLATION AND 1
- PROGRAMMING GUIDE 1
- Contents 3
- 496791 iii 5
- 1. INTRODUCTION 7
- 2 496791 8
- 496791 3 9
- System Features 10
- Detectors 10
- 9955 Radio Expander 10
- Partioned or Single System 11
- User Control 11
- Configurations 11
- 6 496791 12
- 2. Technical Description 13
- Compatible Equipment 14
- Control Unit PCB 15
- 9954 Expander 16
- 3. INSTALLATION 17
- Cabling Keypads and Expanders 18
- Fitting the System 19
- Fitting the Control unit Case 19
- Fitting a 9930 Keypad 19
- Wiring the Control Unit 20
- Cable Entries 20
- Mains Connection 20
- Remote Keypads 21
- 16 496791 22
- Detector Circuit Connections 23
- 18 496791 24
- Connecting Expanders 25
- Expander Addressing 26
- Using Programmable Outputs 26
- Wiring Keyswitches 27
- Using a Communicator 28
- Statutory Information 29
- Application 29
- Compatible PABXs 29
- Approval 29
- Safety Notice 30
- Connecting the Telephone Line 31
- 26 496791 32
- 496791 27 33
- Fitting a Battery 34
- Initial Start Up 35
- 30 496791 36
- 4. Programming 37
- 32 496791 38
- 496791 33 39
- 34 496791 40
- 496791 35 41
- 36 496791 42
- 496791 37 43
- 38 496791 44
- Communications Programming 45
- 40 496791 46
- 496791 41 47
- 42 496791 48
- Leaving Programming Mode 49
- Engineer Reset 49
- Re-entering Programming Mode 49
- Programming Reference 50
- Country Defaults (Command 0) 50
- 496791 45 51
- 46 496791 52
- 496791 47 53
- 48 496791 54
- 496791 49 55
- RedCare Reset (Command 23) 56
- Status Display (Command 28) 57
- 52 496791 58
- System Reset (Command 33) 59
- PA Reset (Command 34) 59
- Alarm Abort (Command 36) 59
- 54 496791 60
- Bell Delay (Command 41) 61
- 56 496791 62
- CSID Code (Command 50) 63
- Abort Reset (Command 53) 64
- BVVO Supervision (Command 54) 64
- Sounder Tamper (Command 59) 65
- 60 496791 66
- 496791 61 67
- 62 496791 68
- 496791 63 69
- 64 496791 70
- 496791 65 71
- 66 496791 72
- 496791 67 73
- Call Mode (Command 101) 74
- Reporting Type (Command 103) 75
- 70 496791 76
- Dynamic Test (Command 108) 77
- Rings to Answer (Command 112) 78
- Access Mode (Command 114) 78
- Account Number (Command 117) 79
- 74 496791 80
- 496791 75 81
- 76 496791 82
- Report Mode (Command 131) 83
- 78 496791 84
- 496791 79 85
- 80 496791 86
- 496791 81 87
- Partition Programming 88
- Introduction 88
- Command Changes 89
- 84 496791 90
- ACPO DD243: 2002 Compliance 91
- Alarm Filtering 92
- 5. Testing 93
- Keypad and Event Log Displays 94
- 496791 89 95
- Printing the Log 96
- 496791 91 97
- 92 496791 98
- 496791 93 99
- 94 496791 100
- 496791 95 101
- DECLARATION OF CONFORMA NCE 102
Prodotti e manuali riguardandi Sistemi di controllo di accesso Cooper Security 9853
(44 pagine)© 2020, manymanuals.it. Tutti i diritti riservati | 0.049 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commenti su questo manuale