Cooper Security 9853 Guida di Installazione Pagina 61
- Pagina / 102
- Indice
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
4. Programming
496791 55
keypad ET terminals. In a single system, do not attempt to fit two
lockswitches.
To set the system the user first enters their access code at a
keypad or operates a keyswitch. The control unit starts the exit
tone. Note that the exit time is infinite in this option. The user then
operates the final exit zone and turns the key in the lock switch to
“locked”. The system sets seven seconds after the lock switch
contacts open.
To unset the system the user turns the lock switch to “unlocked”
(closing the lock switch contacts). The keypads start a continuous
tone. At this point the user can lock the lockswitch again without
causing any alarm. When the user opens the final exit zone the
control unit starts the entry timer. The user completes entry by
unsetting the system in the normal way. Note that when the user
unlocks the lockswitch the control unit disables Alarm Confirma-
tion. The control unit enables Alarm Confirmation again if the user
locks the lockswitch without starting the entry timer.
If an intruder opens the final exit door without first unlocking the
lockswitch then the control unit immediately starts an unconfirmed
alarm. If the intruder goes on to violate another zone and you
have enabled Alarm Confirmation then the control unit sends a
confirmed alarm.
Note that the keypads give a double beep confirmation tone at the end of all
setting modes.
If you select Timed (options 0), Terminate (option 1), or Final Door (option 2)
exit modes the system allows a seven second settling time after pressing an
exit terminate button or closing a final door.
System Auto Re-Arm (Command 40)
This Command lets you program the number of times that the system will re-
arm when the bell delay expires. The system re-arms all closed zones. Select
option 0 to make the system never re-arm (the system will go into alarm once
only). Select options 1 to 4 to make the system re-arm once, twice, three
times or always.
Use this Command in conjunction with Command 35 - First Circuit Response.
If the system has rearmed, then when a user enters the system through the
entry route the control unit will give an audible internal alarm in place of the
normal entry tone.
Bell Delay (Command 41)
When the system is set and (for example) an intruder violates a zone, then
the system waits for the programmed Bell Delay before operating the exter-
- INSTALLATION AND 1
- PROGRAMMING GUIDE 1
- Contents 3
- 496791 iii 5
- 1. INTRODUCTION 7
- 2 496791 8
- 496791 3 9
- System Features 10
- Detectors 10
- 9955 Radio Expander 10
- Partioned or Single System 11
- User Control 11
- Configurations 11
- 6 496791 12
- 2. Technical Description 13
- Compatible Equipment 14
- Control Unit PCB 15
- 9954 Expander 16
- 3. INSTALLATION 17
- Cabling Keypads and Expanders 18
- Fitting the System 19
- Fitting the Control unit Case 19
- Fitting a 9930 Keypad 19
- Wiring the Control Unit 20
- Cable Entries 20
- Mains Connection 20
- Remote Keypads 21
- 16 496791 22
- Detector Circuit Connections 23
- 18 496791 24
- Connecting Expanders 25
- Expander Addressing 26
- Using Programmable Outputs 26
- Wiring Keyswitches 27
- Using a Communicator 28
- Statutory Information 29
- Application 29
- Compatible PABXs 29
- Approval 29
- Safety Notice 30
- Connecting the Telephone Line 31
- 26 496791 32
- 496791 27 33
- Fitting a Battery 34
- Initial Start Up 35
- 30 496791 36
- 4. Programming 37
- 32 496791 38
- 496791 33 39
- 34 496791 40
- 496791 35 41
- 36 496791 42
- 496791 37 43
- 38 496791 44
- Communications Programming 45
- 40 496791 46
- 496791 41 47
- 42 496791 48
- Leaving Programming Mode 49
- Engineer Reset 49
- Re-entering Programming Mode 49
- Programming Reference 50
- Country Defaults (Command 0) 50
- 496791 45 51
- 46 496791 52
- 496791 47 53
- 48 496791 54
- 496791 49 55
- RedCare Reset (Command 23) 56
- Status Display (Command 28) 57
- 52 496791 58
- System Reset (Command 33) 59
- PA Reset (Command 34) 59
- Alarm Abort (Command 36) 59
- 54 496791 60
- Bell Delay (Command 41) 61
- 56 496791 62
- CSID Code (Command 50) 63
- Abort Reset (Command 53) 64
- BVVO Supervision (Command 54) 64
- Sounder Tamper (Command 59) 65
- 60 496791 66
- 496791 61 67
- 62 496791 68
- 496791 63 69
- 64 496791 70
- 496791 65 71
- 66 496791 72
- 496791 67 73
- Call Mode (Command 101) 74
- Reporting Type (Command 103) 75
- 70 496791 76
- Dynamic Test (Command 108) 77
- Rings to Answer (Command 112) 78
- Access Mode (Command 114) 78
- Account Number (Command 117) 79
- 74 496791 80
- 496791 75 81
- 76 496791 82
- Report Mode (Command 131) 83
- 78 496791 84
- 496791 79 85
- 80 496791 86
- 496791 81 87
- Partition Programming 88
- Introduction 88
- Command Changes 89
- 84 496791 90
- ACPO DD243: 2002 Compliance 91
- Alarm Filtering 92
- 5. Testing 93
- Keypad and Event Log Displays 94
- 496791 89 95
- Printing the Log 96
- 496791 91 97
- 92 496791 98
- 496791 93 99
- 94 496791 100
- 496791 95 101
- DECLARATION OF CONFORMA NCE 102
Prodotti e manuali riguardandi Sistemi di controllo di accesso Cooper Security 9853
(44 pagine)© 2020, manymanuals.it. Tutti i diritti riservati | 0.040 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commenti su questo manuale