Cooper Security 9853 Guida di Installazione Pagina 52
- Pagina / 102
- Indice
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
4. Programming
46 496791
signal (internal sounders pulsing “Dee Dah Dee Dah...”).
Fire alarms operate whether the system is set or unset,
and will always trigger communications if fitted.
Normal Alarm (NA)(Key in 03) A zone programmed as ‘Normal Alarm’ will
start an alarm when the system is set.
24 Hr Zone (24) (Key in 04) This zone causes an internal alarm if violated
when the system is unset, and a full alarm if the system is
set. Providing the Installer programs 24hr zones with
‘Omit Allow’, the user can omit 24 hour zones in Day
mode. Note that the control unit re-instates all 24Hr zones
if anyone sets the system.
Final Exit (FE) (Key in 05) Zones of this type must be the last detector to
be activated on exit, or the first to be activated on entry.
You can use zones of this type to finally set the system,
or to start the entry procedure. Use Command 39 to set
the exit mode type.
Entry Route (ER) (Key in 06) Use this zone type for detectors sited between
the Final Exit door/detector and a keypad. If an ‘Entry
Route’ zone is violated when the system is set, an alarm
will occur. If the entry/exit timer is running when an Entry
Route zone is violated then no alarm occurs until the
entry/exit timer expires.
Shock
Analyser (SA) (Key in 07) You can apply this zone type to zones 1 to 4.
The system will not accept the attribute for zones 5 to 40.
(See also “Zone Attributes - Sensitivity”.)
Technical (TC) (Key in 08). Use this zone type when you want to monitor
equipment, for example a freezer, without raising a full
alarm. If a technical alarm zone is activated while the
system is set, the system makes no audible alarm.
However, when a user unsets the system the keypad
indicates a fault.If a technical alarm zone is activated
while the system is unset then the system starts a pulsed
tone from the keypad. If programmed, the control unit also
starts communication. When a user enters a valid code
the keypad stops the tone and displays the zone.
Key Box (KB) (Key in 09). This zone type is for use in Scandinavia only.
When a zone of this type is required, the Installer con-
nects the alarm wires of the zone to a special external
key box and the tamper wires to the box enclosure switch.
When someone opens the box the control unit logs the
- INSTALLATION AND 1
- PROGRAMMING GUIDE 1
- Contents 3
- 496791 iii 5
- 1. INTRODUCTION 7
- 2 496791 8
- 496791 3 9
- System Features 10
- Detectors 10
- 9955 Radio Expander 10
- Partioned or Single System 11
- User Control 11
- Configurations 11
- 6 496791 12
- 2. Technical Description 13
- Compatible Equipment 14
- Control Unit PCB 15
- 9954 Expander 16
- 3. INSTALLATION 17
- Cabling Keypads and Expanders 18
- Fitting the System 19
- Fitting the Control unit Case 19
- Fitting a 9930 Keypad 19
- Wiring the Control Unit 20
- Cable Entries 20
- Mains Connection 20
- Remote Keypads 21
- 16 496791 22
- Detector Circuit Connections 23
- 18 496791 24
- Connecting Expanders 25
- Expander Addressing 26
- Using Programmable Outputs 26
- Wiring Keyswitches 27
- Using a Communicator 28
- Statutory Information 29
- Application 29
- Compatible PABXs 29
- Approval 29
- Safety Notice 30
- Connecting the Telephone Line 31
- 26 496791 32
- 496791 27 33
- Fitting a Battery 34
- Initial Start Up 35
- 30 496791 36
- 4. Programming 37
- 32 496791 38
- 496791 33 39
- 34 496791 40
- 496791 35 41
- 36 496791 42
- 496791 37 43
- 38 496791 44
- Communications Programming 45
- 40 496791 46
- 496791 41 47
- 42 496791 48
- Leaving Programming Mode 49
- Engineer Reset 49
- Re-entering Programming Mode 49
- Programming Reference 50
- Country Defaults (Command 0) 50
- 496791 45 51
- 46 496791 52
- 496791 47 53
- 48 496791 54
- 496791 49 55
- RedCare Reset (Command 23) 56
- Status Display (Command 28) 57
- 52 496791 58
- System Reset (Command 33) 59
- PA Reset (Command 34) 59
- Alarm Abort (Command 36) 59
- 54 496791 60
- Bell Delay (Command 41) 61
- 56 496791 62
- CSID Code (Command 50) 63
- Abort Reset (Command 53) 64
- BVVO Supervision (Command 54) 64
- Sounder Tamper (Command 59) 65
- 60 496791 66
- 496791 61 67
- 62 496791 68
- 496791 63 69
- 64 496791 70
- 496791 65 71
- 66 496791 72
- 496791 67 73
- Call Mode (Command 101) 74
- Reporting Type (Command 103) 75
- 70 496791 76
- Dynamic Test (Command 108) 77
- Rings to Answer (Command 112) 78
- Access Mode (Command 114) 78
- Account Number (Command 117) 79
- 74 496791 80
- 496791 75 81
- 76 496791 82
- Report Mode (Command 131) 83
- 78 496791 84
- 496791 79 85
- 80 496791 86
- 496791 81 87
- Partition Programming 88
- Introduction 88
- Command Changes 89
- 84 496791 90
- ACPO DD243: 2002 Compliance 91
- Alarm Filtering 92
- 5. Testing 93
- Keypad and Event Log Displays 94
- 496791 89 95
- Printing the Log 96
- 496791 91 97
- 92 496791 98
- 496791 93 99
- 94 496791 100
- 496791 95 101
- DECLARATION OF CONFORMA NCE 102
Prodotti e manuali riguardandi Sistemi di controllo di accesso Cooper Security 9853
(44 pagine)© 2020, manymanuals.it. Tutti i diritti riservati | 0.096 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commenti su questo manuale