Cooper Security 9853 Guida di Installazione Pagina 62
- Pagina / 102
- Indice
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
4. Programming
56 496791
nal sounder. The system then operates the external sounder for the pro-
grammed Bell Duration. See “Programming Commands” for the Command
options.
Note: Command 41 has no effect if Alarm Confirmation (Command 89) is enabled
and either:
External Sounder (Command 162) is set to option 0, or
Internal Sounder (Command 161) is set to option 0. or
Alarm Response Mode (Commands 47, 63, 73 and 77) does not require
communications.
Bell Duration (Command 42)
This Command lets you set the length of time the system will operate the
external sounder during an alarm. See “Programming Commands” for the
Command options.
Level A Entry Time (Command 43)
This Command lets you set the Entry Time for Full Set or Partition A. See
“Programming Commands” for the Command options. The time starts when a
user opens any Final Exit zone.
Level A Exit Time (Command 44)
This Command lets you set the Exit Time for Full Set or Partition A. See
“Programming Commands” for the Command options.
Entry/Exit Tone Volume (Command 45)
In a single system use this Command to set the volume of entry/exit tones
from the internal sounder. If you select option 0 then the internal sounder
gives no entry/exit tones. If you select option 1 then the internal sounder
gives quiet entry/exit tones, while option 9 gives the loudest entry/exit tones.
The internal sounder demonstrates the volume of the tone when you enter
the digit. Note that this Command is not available in a partitioned system.
Tamper Alarm Annunciation (Command 46)
In a single system use this Command to chose which sounders the control
unit will activate for a tamper alarm while the system is unset.
Option 0 selects internal sounders only.
Option 1 selects keypad sounders only.
Option 2 selects internal sounders and keypad sounders.
This Command is not available in a partitioned system.
Partition A Alarm Response (Command 47)
If you have programmed the system for partitions then the following options
are available:
- INSTALLATION AND 1
- PROGRAMMING GUIDE 1
- Contents 3
- 496791 iii 5
- 1. INTRODUCTION 7
- 2 496791 8
- 496791 3 9
- System Features 10
- Detectors 10
- 9955 Radio Expander 10
- Partioned or Single System 11
- User Control 11
- Configurations 11
- 6 496791 12
- 2. Technical Description 13
- Compatible Equipment 14
- Control Unit PCB 15
- 9954 Expander 16
- 3. INSTALLATION 17
- Cabling Keypads and Expanders 18
- Fitting the System 19
- Fitting the Control unit Case 19
- Fitting a 9930 Keypad 19
- Wiring the Control Unit 20
- Cable Entries 20
- Mains Connection 20
- Remote Keypads 21
- 16 496791 22
- Detector Circuit Connections 23
- 18 496791 24
- Connecting Expanders 25
- Expander Addressing 26
- Using Programmable Outputs 26
- Wiring Keyswitches 27
- Using a Communicator 28
- Statutory Information 29
- Application 29
- Compatible PABXs 29
- Approval 29
- Safety Notice 30
- Connecting the Telephone Line 31
- 26 496791 32
- 496791 27 33
- Fitting a Battery 34
- Initial Start Up 35
- 30 496791 36
- 4. Programming 37
- 32 496791 38
- 496791 33 39
- 34 496791 40
- 496791 35 41
- 36 496791 42
- 496791 37 43
- 38 496791 44
- Communications Programming 45
- 40 496791 46
- 496791 41 47
- 42 496791 48
- Leaving Programming Mode 49
- Engineer Reset 49
- Re-entering Programming Mode 49
- Programming Reference 50
- Country Defaults (Command 0) 50
- 496791 45 51
- 46 496791 52
- 496791 47 53
- 48 496791 54
- 496791 49 55
- RedCare Reset (Command 23) 56
- Status Display (Command 28) 57
- 52 496791 58
- System Reset (Command 33) 59
- PA Reset (Command 34) 59
- Alarm Abort (Command 36) 59
- 54 496791 60
- Bell Delay (Command 41) 61
- 56 496791 62
- CSID Code (Command 50) 63
- Abort Reset (Command 53) 64
- BVVO Supervision (Command 54) 64
- Sounder Tamper (Command 59) 65
- 60 496791 66
- 496791 61 67
- 62 496791 68
- 496791 63 69
- 64 496791 70
- 496791 65 71
- 66 496791 72
- 496791 67 73
- Call Mode (Command 101) 74
- Reporting Type (Command 103) 75
- 70 496791 76
- Dynamic Test (Command 108) 77
- Rings to Answer (Command 112) 78
- Access Mode (Command 114) 78
- Account Number (Command 117) 79
- 74 496791 80
- 496791 75 81
- 76 496791 82
- Report Mode (Command 131) 83
- 78 496791 84
- 496791 79 85
- 80 496791 86
- 496791 81 87
- Partition Programming 88
- Introduction 88
- Command Changes 89
- 84 496791 90
- ACPO DD243: 2002 Compliance 91
- Alarm Filtering 92
- 5. Testing 93
- Keypad and Event Log Displays 94
- 496791 89 95
- Printing the Log 96
- 496791 91 97
- 92 496791 98
- 496791 93 99
- 94 496791 100
- 496791 95 101
- DECLARATION OF CONFORMA NCE 102
Prodotti e manuali riguardandi Sistemi di controllo di accesso Cooper Security 9853
(44 pagine)© 2020, manymanuals.it. Tutti i diritti riservati | 0.029 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commenti su questo manuale