Cooper Security 9853 Guida di Installazione Pagina 64
- Pagina / 102
- Indice
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
4. Programming
58 496791
Setting Time and Date (Command 51)
The system has an internal clock/calendar which it uses to date stamp the
log print-out. To set the system’s clock/calendar to the correct time and date:
1. Enter programming mode (if you are not already there).
2. Key in 51 at the keypad.
The display shows the current date, for example:
3. Key in two digits for the day number and press . Use a leading zero
for the first nine days of the month.
4. Key in the two digits for the month number and press . Use a leading
zero for January to September.
5. Key in the two digits of the year and press .
The display shows the current time, for example:
6. Key in two digits for the hours of the day and press . Use the 24-hour
clock.
7. Key in two digits for the minutes and press .
The keypad sounder gives a double “bleep” and the display shows
“Installer Mode”. The system sets its internal clock/calendar to the time
you have given it.
Omit Tamper Allowed (Command 52)
This Command ensures that the control unit omits the tamper contacts as
well as the alarm contacts when a user omits a zone. Note that you must give
the zone the omit attribute to allow the user to omit a zone.
Option 0 The control unit omits alarm contacts only
Option 1 The control unit omits both alarm and tamper contacts when the
user omits a zone.
Abort Reset (Command 53)
Option 0 Ensures that reset after abort is the same as system reset (see
Command 33).
Option 1 Enables customer reset after an abort.
BVVO Supervision (Command 54)
If the alarm system must meet BVVO radio supervision requirements then
select option 1. Once selected, the control unit will give a warning on the
keypad display when a user tries to set the system if a detector has lost
contact with the control unit for more than 15 minutes. If a detector loses
contact for more than two hours the control unit raises an alarm (see Com-
mand 128).
- INSTALLATION AND 1
- PROGRAMMING GUIDE 1
- Contents 3
- 496791 iii 5
- 1. INTRODUCTION 7
- 2 496791 8
- 496791 3 9
- System Features 10
- Detectors 10
- 9955 Radio Expander 10
- Partioned or Single System 11
- User Control 11
- Configurations 11
- 6 496791 12
- 2. Technical Description 13
- Compatible Equipment 14
- Control Unit PCB 15
- 9954 Expander 16
- 3. INSTALLATION 17
- Cabling Keypads and Expanders 18
- Fitting the System 19
- Fitting the Control unit Case 19
- Fitting a 9930 Keypad 19
- Wiring the Control Unit 20
- Cable Entries 20
- Mains Connection 20
- Remote Keypads 21
- 16 496791 22
- Detector Circuit Connections 23
- 18 496791 24
- Connecting Expanders 25
- Expander Addressing 26
- Using Programmable Outputs 26
- Wiring Keyswitches 27
- Using a Communicator 28
- Statutory Information 29
- Application 29
- Compatible PABXs 29
- Approval 29
- Safety Notice 30
- Connecting the Telephone Line 31
- 26 496791 32
- 496791 27 33
- Fitting a Battery 34
- Initial Start Up 35
- 30 496791 36
- 4. Programming 37
- 32 496791 38
- 496791 33 39
- 34 496791 40
- 496791 35 41
- 36 496791 42
- 496791 37 43
- 38 496791 44
- Communications Programming 45
- 40 496791 46
- 496791 41 47
- 42 496791 48
- Leaving Programming Mode 49
- Engineer Reset 49
- Re-entering Programming Mode 49
- Programming Reference 50
- Country Defaults (Command 0) 50
- 496791 45 51
- 46 496791 52
- 496791 47 53
- 48 496791 54
- 496791 49 55
- RedCare Reset (Command 23) 56
- Status Display (Command 28) 57
- 52 496791 58
- System Reset (Command 33) 59
- PA Reset (Command 34) 59
- Alarm Abort (Command 36) 59
- 54 496791 60
- Bell Delay (Command 41) 61
- 56 496791 62
- CSID Code (Command 50) 63
- Abort Reset (Command 53) 64
- BVVO Supervision (Command 54) 64
- Sounder Tamper (Command 59) 65
- 60 496791 66
- 496791 61 67
- 62 496791 68
- 496791 63 69
- 64 496791 70
- 496791 65 71
- 66 496791 72
- 496791 67 73
- Call Mode (Command 101) 74
- Reporting Type (Command 103) 75
- 70 496791 76
- Dynamic Test (Command 108) 77
- Rings to Answer (Command 112) 78
- Access Mode (Command 114) 78
- Account Number (Command 117) 79
- 74 496791 80
- 496791 75 81
- 76 496791 82
- Report Mode (Command 131) 83
- 78 496791 84
- 496791 79 85
- 80 496791 86
- 496791 81 87
- Partition Programming 88
- Introduction 88
- Command Changes 89
- 84 496791 90
- ACPO DD243: 2002 Compliance 91
- Alarm Filtering 92
- 5. Testing 93
- Keypad and Event Log Displays 94
- 496791 89 95
- Printing the Log 96
- 496791 91 97
- 92 496791 98
- 496791 93 99
- 94 496791 100
- 496791 95 101
- DECLARATION OF CONFORMA NCE 102
Prodotti e manuali riguardandi Sistemi di controllo di accesso Cooper Security 9853
(44 pagine)© 2020, manymanuals.it. Tutti i diritti riservati | 0.037 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commenti su questo manuale