Cooper Security M-Series Manuale delle Istruzioni Pagina 26
- Pagina / 71
- Indice
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
20 496478
3. Installation
Installing a Communicator
The 9750 control unit contains a built in communicator on the main PCB. In
addition the control unit can be connected to a separate communication
device using a wiring harness connecting to interface pins on the main PCB.
Built in Communicator
The built in communicator is a 300 Baud Auto Dialling Modem. The communi-
cator can be used for:
• Transmitting alarm signals to alarm receiving equipment at a central
monitoring station using either Scancom Fast Format, Scancom SIA
(Security Industry Association), or Contact ID.
• Connecting to a PC based at a remote engineering centre. By using
Scantronic <Downloader> software, the remote PC can up- or download
system parameters (including the event log and diagnostics), set and
unset the alarm system, and carry out other special functions.
Telephone Line
The built in communicator can be connected directly to an ex-directory line
used exclusively for alarm communications.
Where an exclusive line is not available and other apparatus is connected to
the line, for example an answer machine, the built in communicator provides
a series connection with line divert for the other apparatus. When triggered,
the communicator seizes the line and disconnects the other apparatus while
the communicator is operational. When the communicator has shut down, it
reconnects the other apparatus.
Note: Ideally, no other equipment should be connected to an exclusive line.
Three Way Calling
The 9750 also provides a Three Way Calling facility to make sure the built in
communicator can always use a shared telephone line.
To use this facility, the local exchange must provide the Three Way Calling
service on the customer's line.
Line Monitoring
The 9750 provides functions programmed by commands 106 and 107 to
ensure that the telephone line is connected and working, and to indicate a
line failure:
• While communication is enabled Line Monitor continually checks the
line voltage to ensure that the line is connected.
• Line Integrity (programming command 107) checks the line to make
sure the local exchange is still responding.
- INSTALLATION AND 1
- PROGRAMMING GUIDE 1
- Contents 3
- 496478 iii 5
- 1. INTRODUCTION 7
- Figure 1. 9750 System Layout 8
- 496478 3 9
- 4 496478 10
- System Features 11
- Detectors 11
- 9755 Hardwired Expander 11
- 9955 Radio Expander 11
- User Control 12
- 2. Technical Description 13
- Control Unit PCB and Case 14
- 9755 Expander 15
- Compatible Equipment 16
- 3. INSTALLATION 17
- Fitting a 9930 LCD Keypad 18
- 496478 13 19
- Wiring the Control Unit 20
- Cable Entries 20
- Mains Connection 20
- Remote Keypads 21
- Connecting Keypads 22
- Exit Terminate Button 22
- Sounders 22
- Detector Circuit Connections 23
- Connecting a 9755 Expander 23
- Using Programmable Outputs 24
- Wiring Keyswitches 25
- Installing a Communicator 26
- Statutory Information 27
- Application 27
- Compatible PABXs 27
- Approval 27
- Safety Notice 28
- Connecting the Telephone Line 29
- 24 496478 30
- 496478 25 31
- Fitting a Battery 32
- Initial Start Up 33
- 28 496478 34
- 4. Programming 35
- 30 496478 36
- 496478 31 37
- 32 496478 38
- * See “5. Testing” 39
- Communications Programming 40
- 496478 35 41
- Leaving Programming Mode 42
- Engineer Reset 42
- Re-entering Programming Mode 42
- Programming Reference 43
- 38 496478 44
- 496478 39 45
- RedCare Reset (Command 23) 46
- Status Display (Command 28) 47
- System Reset (Command 33) 47
- PA Reset (Command 34) 48
- Alarm Abort (Command 36) 48
- 496478 43 49
- CSID Code (Command 50) 50
- 496478 45 51
- 46 496478 52
- 496478 47 53
- Call Mode (Command 101) 54
- Reporting Type (Command 103) 55
- Dynamic Test (Command 108) 56
- Download Mode (Command 110) 57
- Rings to Answer (Command 112) 57
- 52 496478 58
- 496478 53 59
- Report Mode (Command 131) 60
- 496478 55 61
- 56 496478 62
- 5. Testing 63
- 58 496478 64
- 496478 59 65
- 60 496478 66
- 64 496478 70
Prodotti e manuali riguardandi Sistemi di controllo di accesso Cooper Security M-Series
(36 pagine)© 2020, manymanuals.it. Tutti i diritti riservati | 0.042 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commenti su questo manuale